List Price: $440.00
Sale Price: $405.95
Today's Bonus: 8% Off
(EDIT 01/27/2011) My initial review below was written based on an old design that had some quality issues. From my communication with Amazon shoppers like you, and the Consumer Relations folks at Insinkerator, it appears that current models have been redesigned to hopefully eliminate the problems I had. It also appears from those same communications that Insinkerator is going beyond the warranty period to replace some consumers' units when they discover this problem. Because of that I have upgraded my rating to a neutral 3-stars and modified my review somewhat. If you have problems with an existing unit, I also would encourage you to contact Insinkerator support to see what they can do for you. They're very good in my experience when your product is in warranty. I've heard from several folks that Insinkerator has replaced their unit outside of warranty too when they had this problem. Obviously there is some limit to what they will be willing to do, but the call is free. So if you've found this review because of a problem with your existing unit, your first step should be to call Insinkerator at 800-558-5712 and give them a chance to make it right. Post here with your experiences.
(Original Review) This Insinkerator product suffers from a couple of design flaws. Like many here I found a puddle of water under my unit about two years after installing it. Checked into buying a new unit, but at $200 I wasn't going to give in easily. After reading other folks' experience with the unit I opened mine up and found the obvious source of the leak. There is a 1/4" plastic vent hose than helps handle the return hot water after you release the faucet handle. Since it's a non-pressurized unit, all water in the line up to faucet gets returned to the tank after you release the faucet handle. This hose, combined with a plastic overflow tank handles the water return. The root cause of the leaking problem is the type of tubing that was used for this one part. In the hot water heater it sits at near 200F, 24/7/365, and it can't handle the heat. Mine had turned a dark brown to nearly black color and had completely failed where the hose was routed right along the stainless steel tank. Every time we used the heater the return water ended up in our cabinet. Because of this one piece, customers everywhere are replacing their tanks prematurely. It can be fixed if you are handy. Please note that any modification of your unit will void the warranty, and rightfully so. If your unit is under warranty you should call Insinkerator at 800-558-5712 and have them replace it. If you buy a new unit, don't mess with it -it's under warranty. Even if it's out of warranty, give them a call -there's a good chance they'll do right by you. If you do try and repair it, know that you are on your own. Insinkerator strongly advises against any owner-initiated component repair. What I have done has been untested by Insinkerator and they have implemented their own fix in the current product design. Anything that happens during or after any repair you make will be your responsibility. And remember, nothing lasts forever.
HOW TO REPAIR: Basically you have to replace the hose with the right kind, and fortunately it's pretty easy. I recommend silicone tubing (rated to 500F), and you'll need some with 1/8" or 3/16" inside diameter. I bought some from an Amazon seller, 1/8" ID and 3/8" OD with thick 1/8" walls. (Edit: The original tubing is 3/16" ID but I went with 1/8 for a good snug fit. 3/16" ID tubing will also work quite well, and is what I would recommend at this point if you can find it.) Search on Amazon and you'll find what I'm talking about. Unfortunately it's only sold in 10' or longer lengths, and you need less than a foot. If you can find it locally, all the better. For good measure get a couple of small plastic zip ties (cable ties) or the proper sized spring clamp to secure the new tubing.
1) Unplug, drain, and remove the tank. After unplugging the power cord, run water thru the unit till cold water flows out the faucet. Then place a large bowl (1-gallon capacity minimum) under the tank, unscrew the drain screw, and let the tank drain into the bowl. If you can easily shut off the water supply do it now, but it is not necessary as long as no one uses the faucet when you are working on the tank. While draining, remove the three tubes from the top of the tank. One has a spring loaded clip you need to depress to remove the tube and the other two are silicone and plastic tubes that just pull off (might vary a bit based on the age of your unit). Loosen the mounting screws, and when the tank has drained, remove it from your cabinet and find a water resistant place to work on it.
2) Disassemble the tank. Really easy -there is a small screw on the top that holds the two sides of the plastic shell together ... remove it. The two sides of the shell pull apart fairly easily but you might need to muscle it a bit. Once you get them apart, remove them from the unit and place aside. Then remove the temperature dial and put it aside. At this point you will have the guts of the unit with the steel tank encased in a dense styrofoam shell. Take a minute to examine the way it's put together (pictures wouldn't hurt either). You'll most probably easily pick out the problem part -it will probably be very dark and brittle, and one end will be attached to the side of the water inlet port. Cut the hose somewhere before the metal (maybe plastic on yours) water inlet port it attaches to, and you will then be able to remove the upper styrofoam shell. After that you will see where the other end of the defective hose goes -the bottom of the plastic overflow tank. You will need to cut the old zip ties (or maybe spring clamps) at each end of the hose to fully remove the old hose.
3) Inspect and dry the full unit. You may want at this point to remove the other styro shell piece and completely dry everything. At this point I discovered that the leaking water has badly rusted several of the screws holding the two pieces of the stainless tank together. IMHO they should have used stainless steel screws. I wasn't sure whether or not the rust has led to any leak in the tank itself, so I disassembled the stainless tank (fun to do with rusted screws I'll tell you). Mine took a T-10 Torx driver for the screws, and I eventually got them all out. A trip to the hardware store got me some #6 x 3/4" stainless machine screws and lock nuts. If you see anything else besides the hose that could be a problem, you'll need to deal with it for a complete repair.
4) Reassemble the unit, installing the new hose as you go. Put the tank back in the bottom styro shell. Attach one end of the silicone hose to the plastic overflow tank and secure with a zip tie cutting off the excess tie. Put the plastic tank back in the upper styro shell and slide the two back onto the top of the stainless tank. The plastic tank lines up with the silicone hose to the front of the unit. You'll route the hose along the tank flange to the right of the unit just like the old hose was. Once the shell is as far down as it goes, route the hose along the side of the styro shell following the groove for the old hose (not a perfect fit, but that's OK) and then over the top to the water inlet port. Hold it in place and see where you need to cut the silicone hose to fit the port without excess slack in the hose. Then cut the hose, attach it to the port and secure with a zip tie. Replace the thin upper piece of styro over the top of it all and reassemble it all into the plastic shell. Take your time and work the two halves together, making sure to get the power cord grommet correctly into the cutout in the shell. Get the bottom together first then work your way up. Pay attention to the new hose, keeping it tucked in behind the side of the front half of the shell (don't let it end up stuffed behind the back half of the shell. When done properly the shell will snap together nicely, and you may note a slight bulge where the new hose is if you used the thicker silicone tubing like me -that's OK. Put the small screw back into the top the shell, and reinsert the drain screw.
5) Reinstall and test tank. Just reverse the removal steps. Open the faucet until water flows before plugging the tank in. Then use the faucet normally, checking regularly for any leaks. Mine has been leak free for two weeks, and should last for years now.
That's it, and it's probably easier than it sounds. For a grand total of less than $25 (with nine feet of hose left over) I have a fully functional tank again. The rest of the unit is very well made. The tank iteslf is built like a ... well, a tank, so I expect it to last years. Good luck with your home repair efforts if you try. If you have questions or need some of the correct tubing email me at pbj1959 at gmail dot com.
UPDATE 9/13/2010: A couple months now and still no leaks. I've been corresponding with another owner who ended up getting a replacement from Insinkerator. He sent me pics (thanks Jay!) that show they have changed the design of this particular tube that has been causing so many problems. The new design uses a different type of plastic for the tubing and avoids routing it along the steel hot water tank. They also seemed to have added a different type of gasket between the two tank halves. From what I saw, new units with this design won't suffer the same problem I described above, but how to tell whether any one new unit purchased at retail will have this fix incorporated??
Click Here For Most Helpful Customer Reviews >>
Junk. The first unit lasted 14 months. Still under warrenty so I purchased another unit as a spare until first one could be repaired and it leaked out of the box. Am going with Instant hot by Kitchenmade as that unit lasted 8 years.Best Deals for InSinkErator SST-FLTR 2/3-Gallon Stainless Tank and Filtration
Please call Insinkerator and verify the warranty policy before purchasing and installing these types of products.My poor rating is entirely related to the warranty service I attempted to obtain after my SST hot water dispenser quit working after 8 months of operation. During my contact with Insinkerator via the 1-800 number it was revealed that I must have have a copy of my receipt "for professional product installation."
Okay, what kind of a game is this? I do not have a receipt for installation, because I installed it myself using the instructions that were provided in the manual. The manual never specified professional installation required for warranty coverage.
On my further insistence on unit return and replacement, the customer service rep continued "We do not have a repair facility or shipping address. An Insinkerator selected plumber must be dispatched to your location. "You should be aware that you will be liable for the service call and the full unit replacement costs if it is determined the installation was not correct."
Okay, this is rubbish. The unit is a small, plastic, foam and very thin steel tank weighing less than a two pounds. It has two internal components, a 98 cent thermostat and heater element. The water flow is fine, so the thermostat or element quit. Why should a plumber be required to fix an ELECTRICAL PROBLEM?
At the time of purchase I was not aware of other alternatives. I now see that a simple electric hot water pitcher or heat-on-use hot water heater would have been better alternatives and have provided better warranty support.
My advice, keep looking.
Honest reviews on InSinkErator SST-FLTR 2/3-Gallon Stainless Tank and Filtration
I would give it a 0, but Insinkerator does send people out to replace the filter, so they get a 1.The product is good, when it works. The problem is that the quality is terrible, and when it fails, it can cause property damage.
We purchased this product in early 2006, and as of this writing, it has failed three times. The first time, the heating element failed, and Insinkerator replaced it. The second time, the unit leaked all of its contents out, damaging our wooden cabinetry. When they replaced the unit, I wisely put a bucket underneath it. It came in handy when it failed yet again, dumping all of the water into the bucket I placed underneath it.
If you decide to purchase this unit, please make sure that it's accessible for replacement and that you place a bucket underneath it. Check the bucket regularly. Also, make sure that the temperature is set to hot, but not boiling; otherwise, water will constantly run from the dispenser and the unit will burn itself out. Good luck.
Find helpful customer reviews and review ratings for InSinkErator SST-FLTR 2/3-Gallon Stainless Tank and Filtration
Only time will tell, but the SST-FLTR heating replacement appears to be a noticable improvement over the original heating unit. My original instant hot water heater began leaking after about 3 years of use. This replacement has an external dial that allows for temperature adjustment depending on how hot you really want your water. We actually didn't need it to be scalding hot, so we've moved the dial to the 12 o'clock position and it seems to be fine for our purposes. The casing is thick, solid plastic and the connectors and tubing appears to be improved over the early model. The heating unit also seems to be better insulated than the original, so hopefully it will keep the water hotter longer and actually save some energy.My only gripe is with the pricing of the SST-FLTR only. Cheapest that I could find was $199 online, yet my local hardware store sells brand new H770-SS models (dispenser and heating unit) for $179. Same heating unit as the SST-FLTR. I used the heating unit as my replacement and I'll see if I can sell the dispenser part for a few bucks at auction.
No comments:
Post a Comment